Introduction to the Cooling Cooling Cooling:

The role of a steam-seal cooler is to make the turbine-rear steam seal-trains slightly negative pressure, and the-steam pipes continue to enter the auto seal cooler through-steam pipelines and condense it into water for reuse of the boiler.

The knot of the auto seal cooler-and material:

The auto seal cooler is a surface heat exchanger, a horizontal knot-, consisting of water chamber and shell, shell material: carbon steel or stainless steel, pipe materials: stainless steel pipe, copper pipe, etc.

Auto seal cooler knot-:

The water exchanger water side of the auto seal cooler uses four process knots-, its cooling water-enter the water room from the water inlet of the water seal cooler, and then flow into the tube of the shell-when the cooling water is in the heat exchange pipe When flowing, heat exchange with steam in the shell (steam side). Cooling water absorbs a large amount of steam condensation heat, rising water temperature,-later enter the export water room, and overflows the auto seal cooling through cooling water exports. Instrument. The steam from the turbine-rear axis seal, through-auto pipeline, enters the inside of the shell from the auto-seal-seal-seal-entrance. The diversion of the steam flowing through the interval between the interval is constantly flowing between the heat exchange pipes of the tube, and the heat exchange is performed. When most of the steam passes through the outer wall of the heat exchange pipe, it releases a large amount of heat and condenses into water. Excessary from the hydrophobic port and enter the hydrophobic pipeline. Because-steam-some of the air that cannot be condensed, in order to make-steam continuously pass-auto pipelines and enter the auto seal cooler, you need to pull out the gas, and through the steam injection, the air and residual steam are discharged to the atmosphere.

Step installation steps for auto seal cooler:

1. -Can the base of the vapor sealing the cooler is qualified and clean up the foundation surface.

2. Hall out of the auto seal cooler on the basis, adjust the level and elevation position.

3.-Check the location of the cooling device and whether the interface position is correct.

4. Fixed equipment (secondary pouring).

5. Connect the pipeline and electricity-.

Precautions for the installation of auto seal cooler:

1. The equipment should be placed on the flat venue.

2. When hanging, the second-sided steel wire rope is on the outside of the equipment support, and the force is uniform.

3. Equipment should be avoided-the effects of external or external torque.

4. When connecting the pipeline, consider the displacement of the device and the displacement of the pipeline. All interfaces (including valves, instruments, instruments, etc.) should be cleaned up. Disassembly seal (including sundries such as steel plates, cardboards, etc.) should be removed to prevent the pipe port from blocking the mouth.

5. Electric-parameter requirements.

6. Start operation-, the whole system-to be cleaned to prevent the blockage and (or) damage of certain equipment, the pipeline-should consider the use of filters.

7. All takeover-the cover should be uniform-seal to prevent leakage.

8. Tie-conduct-seal-test and eliminate leakage-.

9. Rehabilitation, installation instrument, instrument.

Starting and shutdown:

The operation of the auto seal cooler should pay attention to the following basic steps:

1. British-the exhaust pipe is unblocked-block.

2. The condensate water and hydrophobic pipeline of the cooler should be unblocked.

3. Turn on the cooling water into/outlet valve so that the cooling water circulates in the cooler.

4. Open the auto seal cooler into the steam valve and start the injection.

5. In order to protect the cooling tube of the cooling cooler, the pump should be parked in the auto seal cooler

Steam water heat exchanger

HR high water and Steam water heat exchanger is a type of heat exchange equipment that uses the heat of waste gas and wastewater to heat cooling water. Heating water enters the equipment from the side of the pipe box and passes through a heat exchange surface composed of high 304 stainless steel tubes. There are four processes in total to transfer heat to the heated water, etc.

Tube replacement of tubular oil cooler

When purchasing a column type oil cooler for tube and core replacement, the cooling area should be informed. The cooling forms are divided into LY type light tube (for use) and LYC type fin type. Stainless steel tubes are generally selected for heat exchange and cooling, and purple copper, brass, and titanium tubes can also be selected as heat exchange components according to user needs.

Steam manifold

Our company's main products include: distribution cylinder, collection cylinder, water distributor, water collector, Steam header, and other water tanks, oil tanks, air tanks, cylinders, and other equipment. The distribution cylinder, also known as the distribution drum, is the main supporting equipment for Steam boilers, used in industries such as power generation, petrochemicals, steel, cement, and construction.

Shaft seal cooler

The shaft seal cooler is used to extract the gas-liquid mixture from the Steam seal system of the Steam turbine, preventing Steam from flowing from the end seal to the turbine room and oil system, thereby polluting the environment and damaging the oil quality. Generally, a shaft seal heater (shaft seal cooler) is used to heat condensate and recover shaft seal Steam.

Replacing the tube of the shaft seal heater

Manufacturer of shaft seal heaters, also undertaking pipe replacement and renovation of shaft seal heaters, replacing copper pipes, stainless steel pipes, boiler pipes, etc. According to customer needs, the replacement, repair, installation, and restoration of the relevant shaft seal heater pipes must be carried out. The original equipment must be sent to our company for pipe bundle replacement.

Oil cooler tube replacement and maintenance

We are a manufacturer of oil cooler tube replacement and maintenance. We undertake various types of tube coolers, condensers, oil coolers, chillers, air coolers, condensers, and other heat exchange and cooling tube replacement and renovation projects. Change the material of the pipes, such as copper pipes, stainless steel pipes, titanium pipes, etc.

Replacing pipes for marine oil coolers

Welded steel pipes (also known as slotted pipes and welded pipes) are mainly used for auxiliary machinery in industries such as thermal power generation, chemical industry, and steel, such as condenser and heater pipe replacement, tubular marine oil cooler pipe replacement, oil-water cooler pipe replacement, tubular marine oil cooler pipe replacement, and Le tube cooler pipe replacement.

Steam seal heater tube replacement and renovation

The Steam seal heater adopts a horizontal U-shaped surface heat exchanger for pipe replacement and transformation. The pipe material is stainless steel pipe, and in addition to expansion joint, the pipe also needs to be sealed and welded with the pipe plate; HSn-70-1 tin brass is also used and fixed on the tube plate by expanding the tube.

Steam silencer

Steam silencers are used for a wide range of Steam emission objects in thermal equipment. Various specifications of boiler Steam silencers can be designed and manufactured based on the user's extracted Steam output, Steam pressure, and connection size.

Sampling cooler

Introduction to sampling coolers of soda: Solid sampling cooler is used for power plants, power stations, steel smelting, chemical, textiles, printing and dyeing and other boiler room furnace water and sampling cooler coolant. The sampling cooler can meet the standards of DL/T457-91 in the power industry , Met the sampling test requirements.